CAR ALARM CYCLOPS P165 TOUCH KEY IMMOBILISER

THIS CYCLOP 

P165

TOUCH KEY

IMMOBILISER SYSTEM

Touchkey Immobiliser system. Engine will start only after Touchkey has swiped the receptacle contacts

IS

NEW

IN SEALED BOX

EX-SHOP STOCK

Contents of kit.
Introduction
This Australian Standards approved immobiliser provides two circuits of automatic engine immobilisation operated by an electronically coded touch key making contact with a dash mounted receptacle incorporating a warning light.
Proudly Australian
Designed and engineered in Perth, Western Australia.

Operation
topDisarming procedure
Insert and remove Touch-key from receptacle on dash to disarm the immobiliser.
Auto Arming
The car's engine is automatically immobilised 40 seconds after the engine has stopped. The auto-arming feature is disabled while the system is disarmed and the ignition switch is in the ON position.
Available for light trucks
The $model system is also available for light trucks which use a +24 Volts battery supply, click here to see $model-24V.

Immobilisation
topDual Immobilisation Circuits
The system features two independent 30 Amp rated, normally open immobilisation circuits, which break engine critical signals in the vehcile. Starter motor, fuel pump, fuel injection, main ignition are commonly immobilised circuits.
Safety circuitry incase of power failure
System sources alternate power from ignition if main power is lost.
Third circuit of immobilisation (optional)
Additional immobilisation circuits can be added to conform with insurance company requirements .
Component protection against harsh road conditions
All relays are fully encapsulated to provide protection against dust and moisture.

Controllers
topTwo Touchkey Tags
Encoded digital signature device with 281,000,000,000,000+ code combinations.
Large system memory
Allows system to track four controllers each operating with a independent code. This allows four users to disarm the system, and erasure of indivdual tags.
Controller re-programming
Service technician can delete lost or stolen controllers from memory.

Wiring
topSecurity wiring
All cables extending from the control module are black and same diameter. Identifying wire tags are removed by the installer during installation of the system.
Plug and play for service
Designed to allow easy access for service technicians. Plugs and sockets are located inside the main control module to protect against access by theives.
Security housing
Connector plug is enclosed within module case to prevent access by thief.
Stealth wiring
Cutting any immobilisation wiring will still leave the car secure. Bypassing security is not possible by simply removing the system from the vehicle.

Override
topEmergency Personal Identification Number (PIN) override
If the valid controller are lost, stolen or broken, the user by over-ride the system by enter the secret four digits via the ignition switch .
Alterable PIN
A factory programmed PIN comes standard with each system. It is recommended the owner of the system changes the PIN to a new, easily remembered number .
One shot override
Immobiliser always re-arms to protect vehicle. Re-enter PIN if vehicle needs to be driven after auto-arming has occurred.
PIN card
A record of the factory programmed override PIN is supplied on handy wallet sized card.

Visual Output
topSuper bright red dash LED
This LED flashes to inform user when system is armed. The LED is mounted on the driver's side dash and is visible from outside the window.

Specifications
topCurrent draw
<10mA average while armed
<250mA disarm (and for no more than 39 seconds after ignition is switched off).
Wide Operating voltage
Operating voltage +9VDC to +15VDC.
Operating temperature
-20 degrees to +85 degrees for equipment designed to be installed within vehicle cabin.
Polarity protection
The system circuitry is design to protect it'self against accidental battery polairty reversal. This can happen when replacing the vehicle battery.
Short circuit protection
The power supply wire to the system is protected against an internal fault within the system.

Printed Material
topInstallation Guide
Complete installation guide and specifications for the.
User Guide
Informs the end-user of the system's functions, features and limitations. Open - .

Warranty
topManufacturers warranty on Control module
Guarantees control module is free from manufacturing defects for 24 months from time of purchase .
Manufacturers warranty on Touch-keys
Guarantees Touch-keys and socket are free from manufacturing defects for 12 months from time of purchase .

Standards Compliance
topAustralian Standard for vehicle Immobilisers
AS/NZS 4601:1999.
Manufactured in ISO9001 facility
Built within world standard production facility.
AS/NZS 4601 sundry standards of compliance (or parts thereof)
AS1939 - Degrees of protection provided by enclosures for electrical equipment (IP Codes)
AS3300 - Approval and test specification - General requirements for household and similar electrical appliances
AS/NZS3548 Limits and methods of measurement of radio disturbance characteristics of information technology equipment
AS/NZS3749 - Intruder alarm systems - Road vehicles
AS/NZS4268 - Radio equipment and systems - Short range devices
AS/NZS61000 - Electromagnetic compatibility (EMC)
NZS6300 - Approval and test specification - General requirements for household and similar electrical appliances
ISO7637 - Road vehicles - Electrical disturbance by conduction and coupling
IEC61000 - Electromagnetic compatibility (EMC)
ASTM B117 - Standard practice for operating salt spray (fog) apparatus.