Holden Statesman '93 Vortec Super Charged V8 486BHP

Last dyno run showed 486BHP, with more to come. Exhaust flow and intake temperature limited us to this, water injection would see her comfortably over the 500mark. Look under Forced Induction V8 in the DynoClub section (http://forum.streetcommodores.com.au....php?t=8496428) - currently sitting in 5th spot between alot of blown strokers.

My pride and joy of the last 5 years. Have not spared a single cent on this car, absolutely everything is brand new. Selling car as is without RWC. The only thing holding it back from being completely road legal is the differential. Everything else inc gbox, supercharger/intake work and fuel system is mod plated. This car wouldnt have done 3000km in the last 4 years and has spent all of its time in the garage or being trailered to the dyno. Huge engine bay work including re-spray, everything fully polished and removal of "un-needed" parts. Huge amounts of custom work done by David Ciccotelli. Almost a show quality engine bay. Entire fuel system was done around 6months ago. Would love to see it go to a real enthusiast who can finish what I started - storage and money have become to much of an issue for me to continue on with this car

Spent over $20,000 on the engine/blower/fuel system alone let alone the rest of the vehicle

CAN SUPPLY COMPLETE TXT FILE WITH ALL PARTS AND COST PRICES WHICH IVE BEEN MAINTAINING SINCE PURCHASE - JUST EMAIL @ holden_vk@hotmail.com

$19,900 (No trades or swaps considered)

Car is driveable and available for test driving
Phone on 0402 611 433

ONN02 (ON NOZ) Tropical QLD licence plates (slim front standard rear)
18x8" VT GTS Champagne Rims with brand new 235/40/18 Federal SS-595 tyres all round

All suspension bits under 2000km old
Pedders lowered shocks (sports ryder)
Pedders lowered springs (sports ryder)
Pedders adjustable camber kits (inner and outer)
Pedders diff crossmember mounts (anti axle tramp)
Pedders Z-Bars
Pedders Z-Bar Bushes (front and rear)
Pedders bearing plates
Pedders polished front strut brace

DBA Gold CrossDrilled and Slotted front rotors
DBA Silver Slotted rear rotors
Bendix Advance pads F&R

New top gun leads
New BOSCH Coil (mounted under scuttle)
New NGK-R Plugs
New Waterpump
Fully Reco alternator 1 year ago(alt and alt bracket is fully polished also)
New manual steering rack
New tie rod ends
New engine mounts
New startor motor
New N70ZZ battery (boot mounted in box with air vent - 100% legal)

Pioneer CD Headunit
Kenwood front 6" Speakers (amped)
Kenwood rear 6x9" Speakers (amped)
Sansui 12" boxed sub with Jensen Amp

Engine under 2000km old, only just run in
Full Rebuild with ACL Race series Bearings/Seals/Gaskets
Full Engine Balance
Match Ported
Shot peened Rods
Valve re-grind cylinder head
Machine & fit 16 Guide Liners
Crack tested heads
Resize con-rod tunnels and fit larger con-rod bolts
Rebore and torque plate hone block
Grind crankshaft A/O
Machine extra balancer keyway
O'Ring block and fit stainless O'Rings
ARP Fitment of main caps
Fit copper head gaskets (lower compression to 7.6:1)

KB Hypertectic Pistons & Moly rings
Surecam Custom Grind camshaft (Duration at .050" camlift. inlet: 236? exhaust: 246?)
Premium Rollmaster Timing gear set
High Volume Oil Pump
PowerBond Race Series Harmonic Balancer
ARP Con-Rod Bolt Set
ARP Head Stud set
Double Valve Springs (120ft lb) (Performance Springs)
Adjustable Yella Terra Roller Rockers
Solid Lifters (Crane)
16 Valve Stem Seals

Fully Polished Vortec S-Trim @ 13PSI
Fully Polished Intercooler with stainless steel piping
GFB Stealth FX BOV
Modified fuel rail
Vortec 10:1 Pressure reg
Walbro hi-flow in-tank pump
Bosch 800hp external pump
Redline 1.5L Surgetank
42lbs (440cc/min) F.A.S.T. Injectors
3Bar map sensor
Haltech E6GMX Engine Management

Fully converted to manual
Brand new T56 Gearbox with close ratio 4th/5th (Literally bought this from Mal Wood about 4months ago)
Custom pressure plate - good for 500+ (Direct Clutch Services)
Race Spec button clutch (Mal Wood)
Fully reconditioned Tailshaft
Fully reco Diff - Brand new 3.9 BW Gears + Mini Spool

Sports Steering wheel
Sports Gearknob
Autometer ProComp air/fuel, fuel pressure, oil pressure, water temp, boost & nitrous guages in cups.

Pacemaker extractors into 2.5inch highflow cats/mufflers & rear muffler 2.5"

MOD PLATED