Huber & Suhner Wireless Ethernet Bridge Radio Link

You Are Bidding On A NEW Huber & Suhner 60GHz Wireless Ethernet Bridge

Quantity of 5 available. Please email for bulk / lot pricing. Techncial specification and additional information can be provided upon request. All units are new and under warranty. We support what we sell !!!
Please visit us at www.pavtechdesign.com.au

Description

SENCITY®LINK is designed to work as a point-to-point data link in the 60 GHz unlicensed band. It supports a variety of short range applications up to 800 m (2600 ft). The signal absorption by oxygen and the narrow beam width of the high gain planar antenna allows for high spatial reuse and a high security level.

Applications

LAN extension
Redundant access
Campus connectivity
Disaster recovery
Wireless backhaul
Centralization of IT infrastructure
Temporary connections during events
Mesh and multipoint networking

Benefits

Easy installation - The concept of the SENCITY®LINK allows to the end user to install it as easy as any other network component. The single cable solution reduces the complexity of the installation. The radio unit is connected to the network and supplied with power through a single outdoor rated Cat5e Ethernet cable.

The visual alignment tool allows the user to easily install the link. Immediate operation without the need of additional configuration is granted.

Network performance - Guaranteed full duplex 100 Mbps along the complete range. Unlike typical WLAN equipment the user can transmit a full 100 Mbps over the link.

License free operation - The system has been approved for operation by the ACMA, FCC and Industry Canada authorities.

System administration - To monitor the status and the traffic the user can access the link statistics either via the HTML user interface or by integrating it into a network management tool via SNMP.

Security - The proprietary radio interface does not allow any other system to access the 60 GHz transmitted data. A high level of data security is inherent in the product via signal absorption by atmospheric oxygen and the use of high gain/narrow beam width antennas.

Technical data

General system information

Transmission Capacity: 100 Mbps Full Duplex
Ethernet frame size: max. 1916 bytes
Latency: < 50 μs
Range*: up to 600m
Availability*: up to 99.999%
                                                 *The range depends on the climate zone and the requested availability

Connection

Interface: 100 Base-TX
Cable Length: max. 100m
Signal Wires: CAT 5e
Connector: RJ45 (seal kit included)

Mechanical data

Dimension: 162 x 162 x 89 mm (6.4“ x 6.4“ x 3.5“)
Weight: 2500 g (5.5 lb) terminal
1000 g (2.2 lb) bracket

System administration

Management: SNMP (get / trap)
Web browser-based

Power supply

Standard: PoE (IEEE 802.3af)
Power Consumption: 11 W

Environmental data

ETSI EN 300 019-2-4 T 4.1E for telecommunications equipment non-weather protected locations - extended

Radio Interface

Frequency: 59.375 / 62.225 GHz (FDD)
Modulation: QPSK

Regulatory Compliance

EN 50371, EN 55022, EN 55024, EN 60950-1, EN 302 217-3, EN 302 217-4-2, FCC Part 15, IC RSS210, RIR0302-47, BNA Mitteilung 217 /2008

The Sencity Link comes with the following parts

The two SL 60 terminals (A&B)
Two stainless steel mounting brackets with fine adjustment for azimuth and elevation (small bag with screws and Allen key included as well)
Visual alignment tool
Installation manual
Recovery CD

The kit does not include

Pole mounting bracket (may or may not be needed)
Cat 5 extension cables for outdoor usage
Power over Ethernet Injector
Lightning Protectors

 

Local pickup available, own freight company or courier acceptable.

Postage indicated below is just an estimate and it may vary subject to final postcode.

 Will post worldwide. International buyers, please email for postage prior to bidding.

 Rate is calculated according to www.australiapost.com.au

 

Thank you for looking, feel free to ask questions and happy bidding...