IN STOCK Synthetic Artificial Grass Turf 10SQM ROLL

Synthetic turf should be installed on a compacted base of fine crushed rock at least 50mm thick (more if in a sandy area)
All joins should be attached using Joining tapes and adhesives. Importantly the turf should be in filled with a mixture of SILICA sand (not washed sand or brickies sand) and rubber granules to at least HALF WAY.

Once installed properly you should not be able to pick up the turf.

A solid compacted base is vital, but more importantly the correct amount of fill is vital. The fill not only helps keep the grass upright, but also protects it from UV. Sand fill on its own will compact over time and make the area very hard, and pure rubber will eventually wash away and leave no fill.

 1) Mark off the area that you will install with an outdoor spray can marker. Consider the dimensions of your Turf to try to get as few seams as possible with your layout.

 2) Remove sod, you will need to remove approximately 25mm to 75mm of soil. Ideally, the sub base will be pitched slightly towards the best direction to allow for water drainage to run-off. Also, after the sub base and the Turf is installed, you will want to have the edges of the Turf at an even level with the natural landscape.

 3) Cap Sprinklers. Turn off valves, compact existing ground to "firm it up fully" (you can rent a vibrating plate compactor at most rental centers).  Spray weed/grass killer and place a weed barrier mesh down (not always necessary in all areas).

 4) Sub-Base: It is very important to ensure the sub-base is completely dry before laying any crushed rock to reduce settling and ensure proper compaction for the surface. Once you confirm that the sub-base is dry, add a top layer of crusher dust or a 5mm crushed rock (these types are best so you don't feel any protruding rocks when you walk on your Turf) - ask your local garden supplier or nursery what material local landscapers use under paving bricks, etc.   The purpose is to firm and level your base, 25mm –75mm of base is usually enough, although in some areas of the country where soil is especially unstable you may need up to 100-150mm of base material; just ask a local expert like a nursery, landscape center, or rock yard if you are not sure.  *** Please note if more than 75mm of base material is used, you will also need to increase the amount of soil removal.

5) Spread, and then compact the sub base material twice. Use the vibrating compactor again.

 6) Finishing Sand layer (not always required if crushed rock is adequately smooth). Spread a fine layer of sand (approx. 2-5mm using just an ordinary seed drop spreader) on the surface to make it more level, bags of "play sand" are available at garden suppliers, some hardware stores. You may also use a water-filled sod roller for an even more level surface.

 7) Check surface for depressions. Any depression areas 10mm-20mm or deeper should be filled-in and re-levelled. Although the turf also drains vertically through the drainage holes that are manufactured in the turf, it is still advisable to give the sub-base a slight slope, to avoid any pools of water (slope away from buildings).

 8) Roll out Turf. Position the turf where it goes, be accurate (so you don't cut off turf you actually need). Note: Try to avoid dragging the turf as this may dislodge some crushed rock or sand.

 9) Cut the turf. Cut off excess material so it's easier to work with. Always use a sharp blade in your utility knife! Make sure turf is still positioned where it goes. Now, trim turf more exactly with straight lines. For optimal performance and beauty, make sure the turf is installed exactly over the prepared based.

 10) Seaming. Where two pieces of turf come together you will need to make a seam.  You can always pay a local synthetic grass installer or carpet layer to help you for a few hours with this process if it makes you feel more comfortable although it usually isn't necessary for most. The seams are simply glued together with outdoor turf adhesive and 300mm wide seaming tape.
At the joining seam, a 300mm wide piece of seaming tape should be cut to the length of the seam.  The turf is to be laid seam to seam the way that it should look to ensure it fits tightly together before it is glued. Note: The pattern of turf stitching on the under side must run in the same direction before the two pieces are adhered. Both sides of the turf at the seam must be pulled back in order to install the seam tape. Note: Before adhering both pieces ensure that both edges have been properly trimmed, straight, and will match up perfectly. Lay the seam tape down on the base directly between the two pieces of turf that are to be joined. Apply gluing compound to the entire piece of seam tape with a notched trowel. Place one side of the turf in the middle of the tape (approximately 150mm) to the centre of the tape. Lay the other side of the turf over the middle of the seam tape to match up exactly to the turf that has just been adhered to the tape. Mesh the fibers together with fingers or brush. Note: Allow 24 hours for glue to properly dry. The following procedures can be administered during the drying time, but turf may shift and require repositioning.

11) Infill Preparation.  Once glue has dried, trim off turf so your lawn fits as desired. Next, it is a good idea to nail the perimeter every 500mm-800mm with nails (80-120mm length).  In order to prepare to infill the turf, rake or power broom the turf in the opposite direction that the turf is laying on the roll. This will allow the infill material to infiltrate the turf rapidly and prevent turf blades from getting trapped in the in fill. The infill process will now commence using a standard seed drop spreader with either sand or crumb rubber as an infill.  The infill helps to weigh the turf down, and stabilize the fibers so as to help avoid "matting". Most use sand infill as it is the least expensive compared to rubber infill. Of course rubber is more shock absorbent than sand, so choose what you can afford and prefer, although it is advisable to have at least the top half in rubber infill.  You want to calculate the amount of infill in advance, as you will want to leave around 15mm of grass blade exposed.   As a general rule of thumb, approximately .75 of a kilogram of sand equals around 10mm of in fill height.  Spread the infill in several passes.  As you spread the infill you should make one entire pass on the surface then sweep it down into the fibers, repeating the process until all of your infill has been spread.

 12) Optional Edging. Depending on your yard, you may want to install some type of edging material around your new lawn.  Examples are natural stone, brick, rock borders, metal edging, plastic edging and timber edging (similar to what is used around flower beds) are popular.  

 Congratulations!!! The installation is complete!